16" Hand Impulse Heat Sealing Sealer Machine Poly Heating Element Plastic Sealer

Description: 16" Hand Impulse Heat Sealing Sealer Machine Poly Heating Element Plastic Sealer Feature: Instantly use: -No warm up time needed, Lightweight Design. 8 stalls temperature adjustme impulse manual hand bag sealer to meet any different materials bags. Wide Application: -Built-in fuse for safe using, Easy to use and to clean,ideal for household, retail, produce, grocery Stores, and industrial sealing with a certain quality superiority. Extra Durable Impulse Sealer Machine: -Upgrade Pure copper transformer make sure this tabletop heat implse sealer working life is double longer than normal sealing machines; -High quality electric heating wire and high temperature resistant cloth enable to heat your poly bags seals better. Note: When seal is done, the red light will go off. Keep the handle pressed down for 2-3 seconds to get seals optimal results.Do not use wet cloth to clean the surface of heat sealing strip. How to Use： Step 1 Plug into the powerStep 2 According to the thickness of bags, adjust the sealing timer to 1-8; and level 3 or 4 is enough for most bags; Thicker the bag, higher the level requiredStep 3 No warm-up time needed, Just put the bag on the machine flatStep 4 Press dawn the sealing machine’s arm. When the signal light is off automatically, keeping the handle pressed down for a few seconds would get optimal results 1. No power switch required (auto-control), link the AC power cord with socket, adjust heating time just according to the thickness of sealing-in material; put the plastic bag on the sealing-in surface and press the handle, the circuit will automatically control heating time. The power will automatically shut down when the indicator light goes out. After 1-2 seconds, release the handle to finish sealing. 2. Any damage occurs during sealing is because of over-long heating time, please spin the rotary knob anticlockwise to shorten heating time. 3. Too-short heating time will cause unstable sealing. Please spin the rotary knob clockwise to lengthen heating time 4. If the plastic bag sticks to rubber pressing board, it means the cooling time is insufficient. You must lengthen the cooling time after indicator light extinguishment. Slightly late to release the handle 5. Remain the heating time unchanged after adjustment, and no need to adjust it during continuous service. 6. Keep AC power cord always inserting on the socket, no electricity consumption when there is no sealing. Guide for Replace the Sealing Machine 1.Using the tools to loosen the screws on the sealing machine 2.Remove the old heat sealing strip and heating element 3.Install a new heat sealing element 4.Then tighten the screws Specification: Type: Heat Sealer Material: Plastic Color: Blue Size: 16''(400mm) Sealing Length: 16''(400mm) Source: 110V / 60Hz Power: 300W Max sealing thickness: 0.3mm and 10 mils Suitable for: PE/PP Bags Impluse Sealing for: Power-saving Sealing Width: 3mm Heat Time: 2-3s Plug Type: US Standard Warm Prompt: 1. Always keep the sealing surface clean, avoid any residue oxidation on the surface to reduce ribbon heater and lifespan of heat-resisting fabric. 2. Don't use wet cloth to scrub sealing surface. 3. Worn-out liner under ribbon heater will cause short circuit and finally damage the ribbon heater. So, it is a must to check up liner condition every time you change ribbon heater. Replace a new one once there is any damage. 4. When you have to change the ribbon heater, you must choose a ribbon heater with the same specification to original one. Troubleshooting The following listed cases are excluded to quality issue: 1. Repeated usage of heater strip breaks due to autoxidation, which leads to electricity failure, suggest to replace a new one (oxidation under high-temperature is normal phenomenon) 2. Inner coil burnout or damage caused by overload continuous usage or wrong operation 3. Any man-made damage leads to non-operation cases Note: suggest to keep heating gear between 3-5 mode, it helps to extend the lifespan of machine; long-term working on high-gear will easily lead to burn-up of inner parts. If the inner coil is burnt out, the machine will be disposed as scrap. Package include: 1 x Heat Sealer 1x Impulse sealer heating element 1x ManualBrandUnbrandedMPNDoes Not ApplyModelPFS-400Size16"

Price: 28.58 USD

Location: Dayton, Ohio

End Time: 2023-10-31T14:16:38.000Z

Shipping Cost: N/A USD