Description: Product Specifications: Colors available: White Light, Black Housing. (We also have Blue/Red/Yellow Light, Just leave a message when you can pay.） The power: DC12V +/-10 Wiring length: 0.6meter Material : LED+PVC+ABS Voltage: 12V life span: more than 100000 hours Size: Length: 9” (22.7cm); Height: 3.5” (8.6cm) * Material: Aluminum, ABS Plastic * Fit For (for reference only) Ford F-150: 2004-2014 (Front Grille & Rear Tailgate(Without Rear View Camera)) Ford F-250: 2005-2015 (Front Grille) Ford F-350: 2005-2015 (Front Grille) Ford Edge: 2011-2014 (Sport, Limited, ST, SE, SEL) Ford Explorer: 2011-2016 (Front Grille) Ford EXPEDITION Ford RANGER Etc. maybe different size. Please measure your original Rear and Front logo before you place an order! Product Features: 1:It is easy to install,can be used more than 10000 hours 2:This product should be installed in the original position to replace the original logo(at the back of the car) 3:Using high-quality automotive-specific double-sided adhesive, sticky special strong special lasting! The use of special vacuum plating technology, both to ensure the original car with the standard gloss, but also to ensure high transmittance and brightness uniformity 4:High quality water plating car badge, Laser and Reflective mirror 5:When the license plate lamp is turned on, the car logo light will be turn on too, which shines the logo in the night . 6:Special waterproof and dustproof design! This product is designed for car modification enthusiasts, specially designed during the day and logo does not light, there is no difference with the original logo, LED logo lights will be lit when the vehicle license plate at night light to open the car standard night becomes a dazzling, full of a sense of future technology, high light the distinguished lineage of your car. Installation Notes: Before you begin, prepare the following tools: 1. Flat head screwdriver 2. Phillips screwdriver 3. Insulating tape 4. Towel 5. Pliers 1. First in the box marked with a towel next to the car, with a flat screwdriver pry the car standard, shop towel is to prevent scratches the body 2. Note first double-sided tape stripping the body, when prying force moderate, do not be too fierce, little by little, slowly pry down, clean up the car body and the standard double-sided adhesive 3. Using a Phillips screwdriver to remove the inner compartment of the rear compartment, pay attention to some parts of the clamp, be careful to remove the noise board can see a variety of lines. 4. Now again to install the car standard lights, the car lights to mark the power cord through one of the car standard positioning holes, wear inside the car Tear off the car on the back of the single-sided plastic lights, while pulling the side of the car lights to stick to the car body, pressed. 5. Mark lights installed, and now the power supply. The car to be connected to the license plate lights after the license light power, so when you turn on the night light when the lights will be marked at the same time to find the license plateafter the power connector 6. First unplug the plug, positive and negative stripping a hole, revealing wire core, according to the red on the red, black and black good line, do not forget to use insulating tape wrapped, and finally plug the plug back again! Replace the rear cover noise board!
Price: 46.99 USD
Location: Shanghai
End Time: 2025-01-19T15:00:21.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Unbranded
Manufacturer Warranty: 6 Months
Color: White Light, Black Housing.
Attachment Type: Self-Adhesive
Material: ABS
Features: Easy Installation, Self-Adhesive
Placement on Vehicle: Front, Rear
