4x Fuel Injector FJ1228 For 2002-2017 Nissan Tsuru 1.6L 1597CC L4 1660073C90

Description: Store CategoriesStore CategoriesOther4x Fuel Injector FJ1228 For 2002-2017 Nissan Tsuru 1.6L 1597CC L4 1660073C90 Product Description OE Part Number: FJ1228 1660073C90 Fitment For: Nissan Tsuru 1.6L L4 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 Packing Included: 4 X Fuel Injectors All injectors are serviced as stated below: OHM Tested for electrical shorts Disassembled and externally cleaned Checked for any major cosmetic damage Internally cleaned via numerous ultrasonic baths using special non-hazardous solutions. Back-flushed to remove any internal debris (multi-step process) Pressure/Leak tested, Spray/Flow Tested Flow matched using the very latest in fuel injection calibrating technology Re-assembled with new OEM high quality components (seals, filters etc..) Carefully packaged to ensure safe arrival Attention: Please check our photos very carefully to make sure the photos shown are the same as you want. Please compare the part number with the original part before purchasing! We will not pay your installation fee or return shipping fee due to incompatibility! If the item does not work properly, please contact our customer service before opening the case via e-bay or pay-pal. When you need to return, exchange and refund, please contact us first. NOTE: Followed to avoid any wrong purchase. Please keep the package in good condition if you want to return it. What dose a bad fuel injector cause? 1.Fuel Consumption Increased. 2.Nosie At Idle. 3.Hard To Speed Up. 4.Weak Pedal. 5.Engine shake. 6.Lightning Alarm. How to replace fuel injectors in your car? 1.The metal rod over the fuel injectors is the fuel rail. Use the socket and ratchet to remove the bolts and brackets holding the fuel rail in place. Depending on the model, some engines will need the fuel line disconnected from the fuel rail in order to move the rail. A :Make sure the engine is cold enough to touch. Disconnect the battery. B :Remove plastic engine covers using appropriate socket. Set covers aside. 2.First, disconnect the main fuel line at the end of the rail. There may be an additional line at the other end, so remove that one, too. The fuel rail is held in place by screws or bolts, depending on your car's setup. Remove these screws or bolts. If your wiring travels over the top of the rail, see the next step to disconnect the wiring first. With everything disconnected from the rail, pull it away from the fuel injectors. Most fuel rails are just pressed onto the injector tops, once you've removed the hold down screws or bolts it should pull away, with a little soomph. 3.Using a small standard screwdriver or pick remove the retainer clip from the fuel injector and work the injector from the rail. Keep a shop towel handy to catch excess fuel while removing the injector. Inspect the old fuel injector making sure the sealing O rings are accounted for.Match the new injector to the old unit, some injector replacements can look a little different which is normal. 4.Use clean engine oil to lube the O ring seals preventing seal damage during reassembly. 5.Push the new injector into the fuel rail and reinsert the trainer clip and tighten down the fuel rail. 6.After the job is complete start the engine while using a flashlight to check for leaks to ensure the job was done correctly. Payment PolicyShipping PolicyReturns PolicyPayment Policy Paypal, Visa, and MasterCard are the accepted forms of payment. Please use the eBay checkout system when paying for your order. Immediate payment is required for all orders. Shipping Policy 1. We would send out within 1-3 business days usually . If there is any delay, you will be notified immediately via e- mail . 2. Items will be shipped to buyer's eBay registered address. Please confirm your address before making payment. 3. We will NOT be responsible for any delay during delivery including but not limited to customs postage checking, strike, force majeure etc Returns Policy Out 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. In addition , it allows customers to return new and unused products in their original factory condition for any reason within 30 days from the date of purchase. Notice: 1. All returns must be pre-approved by Autopartm and have a return merchandise authorization (RMA) number.Unauthorized returns will not be accepted. 2. Buyers are responsible for appropriate packing, returning shipping cost, insurance and returning the item in “new” condition. Used items will not be accepted for return. 3. We will replace the returning item with an identical item, issue a full store credit or a full refund. Copyright © 2023 Dianxiaomi

Price: 74.63 USD

Location: Perth Amboy, New Jersey

End Time: 2025-01-28T11:27:00.000Z

Shipping Cost: 0 USD