BROWN & SHARPE 618 Micromaster Surface Grinder Operators Maintenance Manual 0092

Description: Manual Description:Number of Pages: 33 This is a reproduction, not a photocopy, of an original Brown & Sharpe 618 Surface Grinder Operations and Maintenance Manual. If you own one of these machines you need this manual to help keep it running. There is a lot of set up and maintenance diagrams. It even covers the hydraulics. Contents:Chapter I Installing or Relocating the Machine..............................5 Chapter II Operating Controls and Principal Parts............................6 Power Table Travel and Power Cross Feed...........................6 Hand Table Travel and Hand Cross Feed.............................7 Chapter III Setup Adjustments.................................................8 Wheel Spindle.....................................................8 Care and Use of Grinding Wheels...................................9 Longitudinal Table Travel........................................10 Cross Feed.......................................................11 Suggestions on Setup and Operation...............................12 Chapter IV Typical Operations...............................................13 Representative Setups Illustrated and Described.Chapter V Maintenance......................................................16 Lubrication......................................................16 Wheel Spindle....................................................16 Removing the Spindle.............................................16 Antifriction Bearing Spindle Unit................................16 Plain Bearing Spindle Unit ......................................16 Disassembling and Repairing the Plainbearing Spindle Unit........17 Reassembling the PlainBearing Spindle Unit.......................18 Replacing the Spindle Bearing in the Machine.....................19 Possible Sources of Grinding Troubles............................19 Table and Cross Feed Mechanisms..................................19 Electrical Controls..............................................19 Chapter VI Hydraulic System.................................................20 Cleaning Hydraulic Reservoir.....................................20 Adjustment of Pressure Relief Valves.............................20 Hydraulic Operation..............................................20 Table Circuit....................................................21 Table Reversing..................................................21 Cross Feed Circuit...............................................21 Power Down Feed Arrangement......................................21 Hydraulic Maintenance - Table Circuit............................21 Fourcolor Schematic..............................................22 Cross Feed Circuit...............................................23 Chapter VII Grinding Wheels and How to Select Them...........................24 Chapter VIII Optional Mechanisms and Additional Equipment.....................25 Exhaust Attachment...............................................25 Exhaust Nozzle...................................................25 Power Down Feed Arrangement......................................25 Extra Vertical Capacity Parts....................................27 Vertical Rapid Positioning Arrangement...........................27 Illuminated Dust Guard...........................................27 Wet Grinding Attachment..........................................27 Castered Base....................................................28 4 Inch Index Centers.............................................28 High Speed Surface Grinding Attachment...........................29 No. 1 Adjustable Vise............................................29 No. 2 Adjustable Swivel Vise.....................................30 No. 21 Flanged Vise..............................................30 Over the wheel Truing Attachment.................................30 Radius and Angle Wheel Truing Attachment.........................31 Continuous Radius and Tangent Wheel Truing Attachment............32 Magnetic Chucks..................................................32 Sine, PermaSine and Permanent Magnet Sine Plates.................33 Overview:I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. I believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. My manuals are not photocopies. I maintain a high standard of quality in my reproductions. Most of the manuals I reproduce look better than their originals. I have professionally digitally edited every page, and removed stains, wrinkles and handwriting. All of the manuals are printed on thick white paper to withstand shop wear and tear.Visit our eBay Store!We have over 1,100 manuals available. From our shop to yours. We get this. But you get this! Why settle for anything less?We can't make pictures a lot better than the original, but we can fix everything else. Shipping: We ship every M-T-W-T-F except US holidays. All of our manuals are shipped with Delivery Confirmation. We stamp “Do Not Bend” on them to ensure that your manual arrives quickly in good condition. Any package that weighs more than 15.9 oz cannot be shipped First Class, and will be shipped Media Mail. Priority and Express mail options are available to purchase. Since we offer free shipping, we cannot reship manuals for free, due to inaccurate or insufficient addresses. Reshipping Fees for inaccurate or insufficient addresses: $5.00 for the first manual and $2.50 for each additional manual. Service: We have been providing this service to fellow craftsman and machinist for over 20 years. We treat everyone as we would like to be treated. We try to take care of all our customers. We do more than sell manuals, we have a complete woodworking and machine shop. We operate all kinds of machinery everyday.

Price: 40 USD

Location: Nixa, Missouri

End Time: 2024-03-01T21:20:59.000Z

Shipping Cost: 0 USD