Howard Restor-A-Finish 16 oz - 9 Colors - “Restore It

Description: RESTOR-A-FINISH PreviousNext“Restore It – Don’t Strip It!”Restor-A-Finish is a unique finish-penetrating formula that restores wood finishes while blending out minor scratches, blemishes and abrasionsAvailable in nine colors to match almost any wood finish tone; Neutral, Maple-Pine, Golden Oak, Cherry, Walnut, Mahogany, Dark Walnut, Dark Oak, and Ebony BrownWith a simple wipe-on, wipe-off process, most finished wood surfaces that seem to need a complete refinishing job can be restored in a few minutesRemoves white heat rings and water marks, sun fade, oxidation, smoke damage and most other blemishesRestor-A-Finish restores the finish without removing any of the existing finishBefore you go to the extreme of stripping it, restore it Colors Almost any existing wood tone, from a light Birdseye Maple to a dark Jacobean, can be closely matched using one of the nine available finish colors. Restor-A-Finish should be used in a color that best matches your finish. If you are uncertain about which color to use, then choose a color slightly lighter than your finish. It’s recommended that you test Restor-A-Finish in an inconspicuous spot to make sure you like what it does and how it matches the finish. For over 50 years, Howard's Restor-A-Finish has been a standard in the antique industry. Because Restor-A-Finish preserves and restores beauty to the original wood finish, it helps preserve the antiques’ authenticity and value, whereas stripping the finish may literally strip the piece of its value. Restor-A-Finish penetrates faded lacquer, shellac, and varnish finishes to bring back the original color and luster. It restores the depth of grain in wood finishes, going much deeper than temporary “scratch cover” products. Restor-A-Finish penetrates and permanently restores most wood finishes without removing any of the existing finish - this is why it is very popular for antiques. Restor-A-Finish maintains the original "patina" of an antique finish, maintaining its character and value as an antique. To protect the newly restored finish Feed-N-Wax is recommended as a follow-up to Restor-A-Finish.“Restore It – Don’t Strip It!”Permanently revive and restore the original color and luster in one step, without removing any of the existing finish. Most wood finishes that seem to need a complete refinishing job can be completely restored in a few minutes with this simple wipe-on, wipe-off process. White heat rings and watermarks, sun fade, oxidation, smoke damage, and most other blemishes can be quickly blended away. Before you go to the extreme of stripping it, try restoring it! Directions: Restor-A-Finish is a unique finish-penetrating formula that contains a small amount of stain combined with just the right amount of solvent and restoring oils, giving it the unique ability to penetrate and permanently restore most existing finishes without removing any of the existing finish.Cover a small area at a time and immediately wipe dry with a clean soft cloth. Do not pour directly on finish. Always wipe off excess Restor-A-Finish. Choose the color that best matches the finish of your wood. Use either a soft cloth or "super fine" (0000) steel wool. Restor-A-Finish works best when you apply it with a soft cloth. For more severe finish damage like white heat-rings, water marks, light scratches apply with “super fine” (0000) steel wool. However, when using steel wool, first check pressure to be used on an inconspicuous spot because the hardness of finishes varies.When using a soft cloth or steel wool, rub with light pressure but hard enough to blend away the damage. As you restore the finish be sure to periodically check your progress. Always rub with the grain of the wood. Some dry faded finishes will only require a quick wipe-on, wipe-off application and will quickly absorb Restor-A-Finish. Other finishes will require a little more work. Still other finishes may require leaving the Restor-A-Finish on longer so it can penetrate into the finish and restore color and depth of grain deep into the wood. All finishes are different, so testing first may be required. Always wipe off excess Restor-A-Finish.For best results, wait at least 30 minutes and then apply a coat of Howard Feed-N-Wax to protect and maintain the newly restored finish. Then re-apply Feed-N-Wax as needed, or when the finish starts to look dry.Treating carved woods: Restor-A-Finish has saved many hours of labor by quickly restoring color and depth of grain on carved wooden furniture, clocks and picture frames. Simply apply Restor-A-Finish with a small paintbrush or soft toothbrush and wipe dry.** If a high gloss finish should appear dull due to the use of steel wool, polish it out with Restor-A-Shine Polishing Compound. Restore-A-Shine is perfect for the final step in restoring high gloss finishes by buffing away fine scratches only seen in the light. These super fine lines in the finish from a distance creating the look of “dullness” on high gloss finishes and can be easily buffed away with Restor-A-Shine Polishing Compound.PrecautionsFirst test Restor-A-Finish on a small inconspicuous area to check results, penetration into the finish, correct color, and if to use (0000) super fine steel wool or a soft cloth. Apply Restor-A-Finish to a small area at a time and always wipe dry. Be careful to protect fabric, carpets, or linoleum when applying Restor-A-Finish, as it may leave a permanent stain. If spilling does occur, immediately scrub area with soap and water or a stain remover and wipe dry.Shipped within 24 hrs of payment from the Piney Woods of East Texas! Happy to combine multiple items shipped together to save on shipping fees! Free Local pick up by Arrangement @ these Locations Better Half Antique Market113 S. MainHenderson, Texas 75654 The 504 Market504 MethvinLongview, Texas 75601 Thank you for shopping with Miss Ida's Collection!

Price: 12.75 USD

Location: Henderson, Texas

End Time: 2023-12-01T02:20:39.000Z

Shipping Cost: 9.25 USD