Hydraulic Steering Cylinder Seal Seal Kit for SeaStar Outboard Cylinders HS5157

Description: FITMENT: Replacement front seal kit fit for SeaStar pivot / front mount cylinders. COMPATIBLITY: Fits Parts: for HC5340, HC5341, HC5342, HC5343, HC5344, HC5345, HC5346, HC5347, HC5348, HC5358, HC5365, HC5375, HC5394, HC5445, HC6750, HC6751, HC6752, HC6753, HC6754, HC6755 Cylinders. HS5157 KIT CONTAINS: 2pcs Seal Glands; 1pc Pin Wrench; 1pc Seal Gland Assembly Guide Tool; 8pcs Various O-rings for the different cylinders. SUPERIOR MATERIAL: Crafted from High Quality Aluminum Construction with great durability which ensures reliable long-term service. FUNCTION: Used to install the pivot/front hydraulic steering cylinders for seastar. This seal kit fits for most outboard boats with single or twin engines. BENEFITS: Can help you repair leaking/weeping cylinder seals, rebuild the outboard front mount hydraulic cylinders, prevent the leaking of fluid and optimizing efficient performance. NOTICE: Inspect the steering rod itself just making sure there is no severe pitting in the rod or anything that would indicate premature failure of new set of seals. Severely pitted rods will rid up a new set of seals and cause premature failure of the expensive seal job 100% SATISFACTION GUARANTEE: We aim to provide the best service for our customer, if you're not 100% satisfied with our item, simply return it for a full refund in 60 days, no questions asked money back guarantee with 12 months’ warranty. This Front Mount Hydraulic Steering Cylinder Seal Kit is great for use in marine applications! It is critical for you to check the cylinder rod to see whether it has scratches, nicks or damages in anyway. Any damages found, the complete cylinder must be replaced. Failure to replace a damaged steering cylinder will result in seal failure and possible loss of steering. Do not remove shaft from steering cylinder. Bleeding the system to remove any air, compatible with Seastar Hydraulic Oil HA5340 only. Check for smooth operations and full travel of the cylinder. Check for no leaking. Compatibility: Fits front mount cylinder parts: HC5340, HC5341, HC5342, HC5343, HC5344, HC5345, HC5346, HC5347, HC5348, HC5358, HC5365, HC5375, HC5394, HC5445, HC6750, HC6751, HC6752, HC6753, HC6754, HC6755 Model Reference: Seal Kit for HC5345, HC5340 and HC5342 (threaded end gland), HC5347 (Pivot Cylinder, Honda 115-130 specific), HC5348 (Pivot Cylinder, OMC 77-90 specific), HC5365 (Compact Cylinder (threaded end gland)) and HC5394 (SeaRay Compact Cylinder (obsolete) (threaded gland)). Note: The smallest imperfection on the shiny steering rod will cause a new seal to fail real quick. Remove the internal steering rod and then take some 1500 then 2000 grit wet sand paper and go over the full length of the steering rod (take your time!!). Clean rod up, lube it with hydro fluid and carefully reassemble the steering system. Simple to Use: 1. Loosening the Seal Gland Place the pin wrench (supplied in the seal kit) in the holes of a gland, and use a 5/8-inch box wrench on the nut on the port end of the piston rod. Turn counterclockwise on the pin wrench with opposite pressure on the box wrench to loosen the seal gland. 2. Removing the Support Bracket Use a 3/4-inch socket wrench to remove the nut and washer securing the support bracket to the support rod. Do the same to the piston rod nut and washer. Use wrenches on the opposite ends to keep the rods from turning. With hardware gone, pull off the support bracket. 3. Removing the Old Seal Gland Finish unscrewing the old seal gland. If you can't grip it well with your hand, use the pin wrench. Slide it off the piston rod. 4. Installing the New Seal Gland Place the tapered guide tool from the kit on the end of the piston rod and lubricate it and the piston rod well with oil or grease. Carefully slide the new seal gland over the guide and onto the piston rod until it reaches the cylinder. Screw the seal gland into the cylinder, but don't tighten it yet. Remove the guide tool. (it is not part of the final assembly, but you will need it for the other side.) 5. Reinstalling the Support Bracket Reconnect the support bracket to the support rod and piston rod and replace the washers and nuts, tightening the nuts against the washers. You may need to use wrenches on the opposite nuts to tighten sufficiently. 6. Tightening the New Seal Gland Use the pin wrench to tighten the new seal gland while using a 5/8-inch box wrench on the end of the piston rod for counter torque. Package Includes: 2 x Seals Gland/Caps (one for each end of cylinder body) 1 x Pin Wrench Tool (Needed to remove seal caps) 8 x O-rings

Price: 15.76 USD

Location: Bordentown, New Jersey

End Time: 2025-02-02T07:45:40.000Z

Shipping Cost: 0 USD