Power Feed X-Axis 150 Lbs Torque for Bridgeport Type Milling Machines 0-200 RPM

Description: 100% American Buy with confidence Fast Delivery Service & Support PICTURE DESCRIPTION The machine is used for X axis,if you want to used for Y axis,a SUPPORT PLATE will be needed. Our Brand New AS-250-150 X-Axis Power Feed Kit is for Bridgeport and Similar Knee Type Milling Machines. These will fit almost any vertical knee type mill out there with the 5/8" Shaft End, Including but not limited to Bridgeport, Precision Matthews, Grizzly, Enco, Jet, Sharp, Acer, Webb, GMC, Kent, Clark, Supermax, Enco, Turn Pro, Vectrax, Acra, Birmingham, Accu, First...etc. The gear ratio between transmission plastic gear and motor shaft gear is not a whole number. The two gears will not mesh and wear at the same spot, this not only increases durability and longevity but even reduces noise over time. Features 1. Speed adjust knob Speed can be adjust according to operator’s requirement, ranging from 0-9. 2. Jog switch Normally, jog switch should be at “FEED” position. For jog movement, just switch to "0" position. Kept holding the switch until it travels to requires position. Warning 1. Be sure to follow the procedure for jog operation to avoid any damage caused by wrong movement. 2. Make sure the power feed stops before you change the direction. 3. The switch should be in the "OFF" position when the machine is not in use or before plugging. Maintenance 1. Gear cover must be open every 6 month to check whether lubrication for spiral gear is sufficient. Graphite type lubrication is suggested rather than silicon type. 2. Carbon brush cap should be open every 6 month to check if the brush has wore out. Brush should be replace immediately if its length is under 5mm (front and back brush should be replaced together). specifications Parameter Type : X-axisModel : AS-250-150Voltage : 110 V, 60 HzTorque : 150 lbsRotate speed : 0-200 rpmLength : 33 cm (13 inch) Width : 20 cm (7.9 inch) Height : 18 cm (7 inch)Gross weight : 6.5 kg(14.3 lb) IN THE BOX 1 x AS-250-150 X-Axis Power Feed for Milling Machine1 x Set of Necessary Accessories1 x Product Manual feature Brand newX-axis power feed for Bridgeport type milling machinesReversible and auto shut-off at end of cut150 Lbs. torqueVariable speedsLonger lifespanEffortless operationLimit switch for sensitive stopNo loss of dial or hand crankNoiseless direction changesBetter surface smoothnessSmall volume and easy installationExcellent speed control in the entire rangePower table feed won't vibrate or strain in low speedDirection control knob for easy and rapid operationSafety feature to protect transmission gear and electronic components MORE INFORMATION SHIPPING 1. We have Two warehouses located in CA, and NJ, and the item will be shipped from one of them, and only to eBay ADDRESS. Package handling only takes 1 business day at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, pls inform us by Email or leave ebay note if the changes are needed before we send the product. 2. It is beyond our ability to change the address after we ship your item. 3. Orders placed at weekend will be shipped within 2 days. 4. USPS: 3-9 business days. | UPS: 2-6 business days. | FedEx: 2-6 business days. 5. We only ship to the 48 states, and we do not ship to FPO or APO addresses. RETURN We accept returns. Please contact our customer service team immediately if: 1.You changed your mind and wish to request a return 2.Your product was damaged during transit All returns must be directed through Customer Service. Please do not return or post items before obtaining instructions from us. If you do, there is a risk that your returned item may not be identifiable and accepted. Applicable freight fees and a 10% re-stocking fee will be deducted from your refund in cases where you changed your mind about your purchase and wish to return the product. This also applies to orders cancelled while in transit. We ONLY accept returns with original package. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. We will require a picture of the damaged part for verification. The buyer will be liable for the shipping costs associated with warranty claim. ABOUT US ABOUT US We are the leading professional eBay Megastore headquartered in America. We seeks to sell the greatest value products on the market. These items should be of an acceptable quality, fit for purpose, and matching their description. On the odd occasion when things don't go to plan, you can be rest assured that our Customer Support team is here to help! Check out our warranty section for all terms and conditions. We have a highly experienced engineering and technical team who specialise in researching and developing all our products.We benchmark our products against high standards and that¡¯s why our customers keep coming back. Even better, we offer a huge range of spare parts and service support after you purchase your product. So when you shop online with us you can buy with peace of mind. Payment We accept Paypal payment only. Payment should be completed within 4 (Four) days of auction closing. Or unpaid dispute will be filed for closing auction. WARRANTY For your peace of mind, this product comes with a lifetime warranty. We value our customers and wish to make your purchase experience as enjoyable as possible. If something goes wrong with your product, please do not hesitate to contact us for assistance. Please contact us through eBay and include the original purchase information (i.e. your name , address, email and purchase receipt number). On Dec-31-20 at 00:05:39 PST, seller added the following information:

Price: 125.9 USD

Location: Westbury, New York

End Time: 2023-09-15T06:28:39.000Z

Shipping Cost: 0 USD