TARAMPS MD 8000 1ohm 8000Watts Mono Channel Class D Car Audio Amplifier

Description: DescriptionThe MD 8000.1 1 ohm digital amplifier module was carefully developed with the latest technology, offering high output and performance for a wide range of automotive sound systems. Its wide frequency response of 10Hz ~ 10KHz (-3dB) allows it to be used with speakers of a wide range of models, such as subwoofers, woofers, mid-bass, mid-range and phenolic drivers. Available in 1 or 2 ohm versions, it is an amplifier classified as mono, that is, it has a channel with a maximum power of 8000 watts RMS. Due to its diversity, it can be installed in cars, vans, pickups, SUVs to amplify internal sound, such as trunk sound or the famous trio speakers, among other automotive projects such as use in sound walls, trios Goiano, open trunk sound, bob speakers, residential speakers, etc. The power you are looking for for your sound system is here! Technical specifications: * Operating class: class d.This is the designation of an amplifier, class d (also called digital) due to the pwm (pulse width modulation) used in its operation, allowing for a small, efficient amplifier with reduced heating compared to other construction classes. * Number of channels: 01.Number of channels for use in your project, with this specific model you have the option of connecting only 1 channel. * Power @12.6v – 1 ohm: 8000w rms.The power with a voltage of 12.6v volts is related to the operation of the vehicle/power supply. * Power @12.6v – 2 ohms: 5120w rms.The power with a voltage of 12.6v volts is related to the operation of the vehicle/power supply. * Minimum output impedance: 1 ohm.Association with the speaker result, where, for example, we can connect two 2-ohm speakers or four 4-ohm speakers to the channel for this result. * Minimum output impedance: 2 ohms. Association with the speaker result, where, for example, we can connect two 4-ohm speakers or four 8-ohm speakers to the channel for this result. * Minimum input sensitivity: 220mV. Lowest voltage required for maximum results with the amplifier, that is, with low radio volume, we will already achieve good results. * Frequency response: 10hz ~ 10khz (-3db). With the frequency response it is possible to identify the application of the amplifier, so if the speaker or any other type of transducer you are using is included within this response, it means that we can use this product in your project. * Variable low pass crossover (lpf): 90hz ~ 10khz. Lpf or low pass filter (English term) means low pass filter, that is, it allows everything below this reference to be reproduced and everything above this indication will not be used. A common use of this function is to reduce the presence of voice in subwoofers. * Variable high pass crossover (hpf): 10hz ~ 90hz. Hpf or high pass filter (English term), means high pass filter, that is, it allows everything above this reference to be reproduced. The common use of this function is to reduce the presence of bass in door speakers, for example. * Bass boost: freq.: 35hz ~ 55hz (boost: 0 ~ 10db (50hz).Bass boost is the bass boost for the amplifier's sub channel, that is, an "extra" boost for the bass. * Power supply voltage: 9 to 16v.This is the indication of the amplifier's operation where it will have the minimum and maximum voltage for its operation. Outside this specification it will not turn on or activate a protection. * Consumption at rest: 2a.This is the reference for the amplifier's consumption on and without music. * Maximum musical consumption: @12.6vdc: 373.40a.This is the estimated consumption of the amplifier working at minimum impedance playing music at maximum volume. * Maximum consumption in sinusoidal signal: @12.6vdc: 746.90a.Reference for bench/laboratory tests under specific conditions with resistive load, fixed frequency and power supply stable. * Protection system: short circuit at the output, short circuit at the output in relation to GND, low impedance protection, high/low voltage protection and thermal protection.This system exists to protect the operation of the amplifier, it may be related to the output, when we have connections below the minimum impedance, a short circuit in the installation or even speakers with problems.This protection may also occur due to voltages outside the operating range, or even thermal protection that occurs due to conditions in which the amplifier is overheating. * Dimensions: width 22.8cm x height 7cm x depth 41.9cm.Extreme dimensions of the product. * Weight: 6.10kg.Gross weight of the amplifier. We will reciprocate positive feedback for a successful transaction. If you are happy with our service, please leave us feedback. WARNING: Shipping: Shipment of the product in 1 to 4 business days, shipments are by UPS or Fedex, as soon as the contracted service picks up the product, the tracking number is given to you. Please do not charge tracking number if you purchased on Friday night, Saturday and Sunday, we ship products during business hours. Please check your shipping address if it is correct on Ebay, we are not responsible for incorrect addresses, you are responsible for the address you write on ebay. If UPS or Fedex cannot find the buyer at home and the product is returned, we will not refund the shipping cost, we will deduct a 20% fee from the product value for store administrative costs. Stay tuned for tracking number updates We are not responsible for the customs fees charged by your country, each country has its own law, please study the laws before purchase. Orders outside the United States For buyers located outside of the United States, additional fees and taxes may be collected at your destination in accordance with your country's rules. For more information, consult FEDEX and UPS carriers or CUSTOMS in your country before purchasing. WE ARE NOT RESPONSIBLE FOR CUSTOMS FEES CHARGED BY YOUR COUNTRY

Price: 440 USD

Location: sao paulo

End Time: 2024-10-15T18:55:23.000Z

Shipping Cost: 0 USD