Walnut Sand Blaster Carbon Deposition Cleaner Car Intake Valve Cleaning Machine

Description: Automotive Walnut Sand Engine Intake Valve Carbon Decarbon Cleaning Machine 110VAUTOOL HTS558 is a de-carbon device for intake valve cleaning, whose working principle is to blast the walnut media into the intake valve through high-pressure airflow. The carbon deposits on the valve and cylinder wall impacted down. The walnut media and carbon deposit mixture can be recycled through special joints. It can deeply remove the sticky carbon deposits on the intake manifold, intake valve and exhaust valve. Effectively solve the problems of unstable idling, insufficient air intake, insufficient power, and insufficient acceleration. Three-year warranty, lifetime maintenance 1.【Deep removal of carbon deposits】Deeply remove the highly sticky carbon deposits on the intake manifold, intake & exhaust valves.（Solve the problems of unstable idling, insufficient fuel combustion, and reduced air-fuel ratio.)2.【External air source】This enables the walnut sand grit to strike the carbon deposits more powerfully and efficiently.3.【Built-in dust filter】It can separate the recovered walnut sand grit from carbon deposits for recycling.4.【Integrated design】The walnut sand grit can be sprayed and recovered simultaneously.5.【3 year warranty】For damage caused by non-human factors, we promise to resend parts for free within 3 years.What is carbon deposits?There are some hydrocarbon olefin residues attach on engine intake,cylinder when fuel burn in engine not completely. These residues change into hard black shell in high temperature condition , that called carbon deposits. Why need clean carbon deposits? Carbon depositswill decrease air-fuel ratio, cut down engine output power, increase fuel consumption, engine drastic shake on idle status...all the thing will hurt engine deeply. So normally we should clean carbon deposition after every 40000-50000 kilometer trip What is walnut material? It show high performance in the three area: hardness, anti-pressure, wear-resisting. A large amount of pores on surface of walnut sand which provide super adsorption capacity, non-toxic and corrosion preventive. It was hardly dissolved in acid, alkali and water.Walnut grit is a pure natural polish material, its hardness was lower than metal but higher than carbon deposition, it will clean intake pipe and back side of intake valve thoroughly but no damageHow to use?1) Open the cover of AUTOOL HTS558 machine and pour into walnut powder (need 2-4KG ), then put dust guard on walnut powder and close. 2) Connect blasting gun nozzle and recycling hose together (there is a hole on recycling hose) 3) Remove intake manifold of the engine, plug blasting gun into the intake, and turn the crankshaft to close intake valve. Connect high-pressure air pump((not included)) to HTS558. 4) Connect AC power, then start cleaning. The process should last 1-3 minutes(depending on how much carbon build-up) 5) Close AUTOOL HTS558, check-up cleaning effect. Normally, the walnut powder can be reused 5-10 times(depending on how much carbon build-up) Recommend:1 Air pump pressure should more than 0.7Mpa (7bar/102PSI)2 Walnut powder diameter should between 0.4-0.8mm, amount in 2-4KG(4-9LB)3 Cleaning time between 1-3 minutes Bullet point:AUTOOL HTS558 is a special machine for engine Intake pipe and intake valve back side clean. Close intake valve, then spray walnut powder into engine intake via air pump(not include), meanwhile HTS558 will recycle walnut powder by vacuum.Walnut powder residual in intake pipe will go to ashes in high temperature after engine start. This is a closed loop. Walnut powder will impact carbon deposition on inner wall of intake pipe. After thousands of impact, carbon deposition will be clear thoroughly Chemical cleaning agent will corrodes pipe and shortens the lifetime of engine. That is why we need AUTOOL HTS558 to clean carbon deposition in intake pipe. Engine should be closed before clean, then turn crankshaft to close intake valve. AUTOOL HTS558 clean one intake pipe each time, 6 cylinder engine should cleaned 6 times one by one(and so on). Recommend: 1 Air pump pressure should more than 0.7Mpa (7bar/102PSI) 2 Walnut powder diameter should between 0.4-0.8mm, amount in 2-4KG(4-9LB) 3 Cleaning time between 1-3 minutesPackage include: 1x AUTOOL HTS558 unit 2x Spray gun 1x Goggles 1x Recycle hose 1x Recycle hose and spray gun connector Walnut powder not include in package,please get it in local market High pressure air pump is requirement(not include in package)PaymentDelivery detailsReturn PolicyAbout usContact usPayment1. We accept PayPal , Credit card (Visa, Eurocard/MasterCard, Amex, and Switch or Visa/Delta) payment can be accepted ONLY through EBAY. 2. Other payment methods (Bank transfer, Cheque, etc.) are NOT acceptable ! 3. Please make the payment within 3 dayDelivery details1.We will ship according to your EBAY address but sorry that we can not accept P.O.BOX address.Please make sure it’s correct . This will help your product to be received safely and quickly! 2.International Buyers Please Note:1) Please check with your country customs office to determine what these additional Import tariffs costs will be prior to bidding / buying.2) It's the buyer's responsibility to complete clearance when parcel reached your Customs. We are Not responsible for buyers's local taxes, please consult local Customs for Tax Details. Customs rates vary from country to country, please understand.3. Any further queries, please don't hesitate to email us. Thank youReturn PolicyPlease return the item within 30 days after receiving if you are not happy with your purchasing.All returns are expected to be in original conditions, please email us first for return address and instructions.About usWe have been engaged for many years in the line of automobile repair instruments and our corporation is established for the purpose of trustworthiness.We have 2 warehouses that are located in Germany and US.We assure you not only good service but also to be ship as soon as possible.Contact usWe are committed to your satisfaction after your purchase.If you are not satisfied with your purchase in any way please give us an opportunity to try and make it right before leaving feedback.We will answer your questions within 1 working days.Customer Service Hours: M-F: 9:30AM - 18:00PM BST (Beijing Standard Time)

Price: 364.99 USD

Location: Cranbury, New Jersey

End Time: 2023-11-29T07:32:43.000Z

Shipping Cost: 0 USD