Web Cam Front and Rear Camshafts Custom Grind PN# 66474 66475

Description: Web Cam Front and Rear Camshafts Custom Grind PN# 66474 66475 Camshafts look to never have been used.-------------------------------------------------------------------------------------- IF YOU HAVE ANY ISSUES WITH THE ORDER PLEASE MESSAGE ME FIRST I usually answer questions MONDAY through FRIDAY, please allow 24 hours during the week for me to get back to youI take photos of the exact item that you will get, unless I state otherwise.Please look at ALL the pictures, I try to match CURRENT cheaper price (I don’t match past prices). Location: A1005ZXC Rear CamInstallation InformationUpon installation of your Web Cam camshaft, check the following. These operations are very important to engine life, please follow instructions! If your cam is described as a "bolt-in" in the Web Cam catalog / web site, you may skip steps 1-5 below.Check piston to valve clearance. Provide the necessary clearance by removing material from the piston. Minimum clearances: Intake 0.050" - Exhaust 0.080" Check valve to valve clearance. It may be necessary to remove material from the valves or sink valve seat height to head. Check the valve spring retainer to valve guide clearance at maximum lift. Remove material from top of valve guide to provide a minimum of 0.030" clearance. Check for valve spring coil bind at maximum valve lift. Clearance at every coil should be at least 0.015". Be certain that cam and / or rocker arms rotate freely in head or block. Remove material from head, block or rocker arms where necessary. Engine and cam life depend on proper installation. New or reground followers should be used when installing Web Cam profiles. Apply the provided assembly lube to cam lobe and follower surfaces. For proper break-in, after installation of a new camshaft, do not allow your engine to idle below 2000 RPM for the first 30 minutes of use. Valve Timing Information Engines:Bombardier Can-Am Outlander 650 (ATV) (2007-2012) V Twin SOHC 8v Bombardier Can-Am Outlander 800 (ATV) (2006-2008) V Twin SOHC 8v Bombardier Can-Am Renegade 800 (ATV) (2007-2008) FI V Twin SOHC 8vPart # PN-66475Grind # 134CLEARANCE HEAD FOR CAM ROTATION IF NEEDEDINTAKEEXHAUSTValve Lash:.005".008"Valve Lift:.441".441"Duration:Duration @ 0.050:267°268°Lobe Center:112.5°111°Intake Opens21°Before TDCExhaust Opens65°Before BDCIntake Closes66°After BDCExhaust Closes23°After TDCValve timing is checked with zero valve lash @ 0.050 inches of valve lift. Front CamInstallation InformationUpon installation of your Web Cam camshaft, check the following. These operations are very important to engine life, please follow instructions! If your cam is described as a "bolt-in" in the Web Cam catalog / web site, you may skip steps 1-5 below.Check piston to valve clearance. Provide the necessary clearance by removing material from the piston. Minimum clearances: Intake 0.050" - Exhaust 0.080" Check valve to valve clearance. It may be necessary to remove material from the valves or sink valve seat height to head. Check the valve spring retainer to valve guide clearance at maximum lift. Remove material from top of valve guide to provide a minimum of 0.030" clearance. Check for valve spring coil bind at maximum valve lift. Clearance at every coil should be at least 0.015". Be certain that cam and / or rocker arms rotate freely in head or block. Remove material from head, block or rocker arms where necessary. Engine and cam life depend on proper installation. New or reground followers should be used when installing Web Cam profiles. Apply the provided assembly lube to cam lobe and follower surfaces. For proper break-in, after installation of a new camshaft, do not allow your engine to idle below 2000 RPM for the first 30 minutes of use. Valve Timing Information Engines:Bombardier Can-Am Outlander 650 (ATV) (2007-2012) V Twin SOHC 8v Bombardier Can-Am Outlander 800 (ATV) (2006-2008) V Twin SOHC 8v Bombardier Can-Am Renegade 800 (ATV) (2007-2008) FI V Twin SOHC 8vPart # PN-66474Grind # 134CLEARANCE HEAD FOR CAM ROTATION IF NEEDEDINTAKEEXHAUSTValve Lash:.005".008"Valve Lift:.441".441"Duration:Duration @ 0.050:267°265°Lobe Center:112.5°111°Intake Opens21°Before TDCExhaust Opens63.5°Before BDCIntake Closes66°After BDCExhaust Closes21.5°After TDCValve timing is checked with zero valve lash @ 0.050 inches of valve lift.

Price: 641.25 USD

Location: Athens, Georgia

End Time: 2024-08-25T17:30:47.000Z

Shipping Cost: 0 USD