WEB-TC Web-enabled 8-channel thermocouple input module

Description: USB card with 8 thermocouple input channels J, K, R, S, T, N, E and B for temperature acquisition via WEB server. 24-bit resolution. Built-in ambient temperature sensor. The WEB-TC is a thermocouple measueremnt device with a built-in web server. Ypu can connect de device to an ethernet port or hub, start up you browser, and view a current data. The WEB-TC is fully supported by the Universal Library and TracerDAQ. These software programs are included on the CD. Web Interface. The WEB-TC embedded web interface provides access to current data and configuration settings using a standard web browser. Browse to the device's home page by entering the URL tht is printed on the device into the browser. View current thermocouple measueremnts and channel data, and configure hardware options from the device´s home page. Only one user can change configuration options on the device at time. The web interface is built into the device´s firmware. and does not need to be intalled on a computer. No external software required other than a web browser TCP/IP connection. TCP/IP connection A TCP/IP connection is required to acces the web interface. Connect the device´s 10Base-T Ethernet port to a local or wide are network using the supplied Etherned cable, to a sinlge computer trough a hub using the supplied Ethernet cable, or direcly to a computer using standard CAT-5 crossover cable. Features: Temperature and voltage measurements 24-bit resolution 8 thermocouple input channels Supports TC types: J, K, R, S, T, N, E and B Built-in ambient temperature sensor Separate temperature inputs 8 digital bits of Input/Output Technical specificationsDigital input/outputDigital typeCMOSNumber of I/O8 (DIO0 through DIO7)ConfigurationIndependently configured for input or output. Switch selectable output voltages: +5 V and +3.3 VPower on conditionsPower on reset is Input mode except when bits are configured to operate as alarms.Pull-up/pull-down configurationAll pins are connected to 47 kOhm resistors that share a common point accessible at Pin 22 of the device (PU/D). This pin is floating by default and is userconfigurable via external connection. For pull-up mode, connect this pin to Pin 21 (+5V). For pull-down mode, connect this pin to Pin 48 (GND).Digital I/O transfer rate (software paced)Digital input – 50 port reads or single bit reads per second typical. Digital output – 100 port writes or single bit writes per second typical.Input high voltage (+5 V mode)4 V min, 5.5 V absolute max.Input high voltage (+3.3 V mode)2.64 V min, 5.5 V absolute max.Input low voltage (+5 V mode)1 V max., -0.3 V absolute min.Input low voltage (+3.3 V mode)0.66 V max., -0.3 V absolute min.Output low voltage (IOL = 2.5 mA)0.6 V max.Output high voltage (IOH=-2.5 mA)4.3 V min. (+5 V mode), 2.7 V (+3.3 V mode)-Temperature alarmsNumber of alarms 8 (one per digital I/O line)Alarm functionalityEach alarm controls its associated digital I/O line as an alarm output. The input to each alarm may be any of the analog temperature input channels. When an alarm is enabled, its associated I/O line is set to output and driven to the appropriate state determined by the alarm options and input temperature. The alarm configurations are stored in non-volatile memory and are loaded at power on.Alarm input modesAlarm when input temperature > T1 Alarm when input temperature > T1, reset alarm when input temperature goes below T2 Alarm when input temperature < T1 Alarm when input temperature < T1, reset alarm when input temperature goes above T2 Alarm when input temperature is < T1 or > T2 Note: T1 and T2 may be independently set for each alarm. Alarm output modesDisabled, digital I/O line may be used for normal operation Enabled, active high output (digital I/O line goes high when alarm condition is met) Enabled, active low output (digital I/O line goes low when alarm condition is met)Alarm update rate1 second-MemoryEEPROM512 bytes for sensor configurationFLASH2 MB for device configuration and website storage-MicrocontrollerType One high-performance 8-bit RISC microcontroller (isolated) One high-performance 16-bit RISC microcontroller (non-isolated) -PowerSupply current Continuous mode440 mA max.External power input+5 VDC ± 5% (+5 VDC power supply provided)External power supply (included)MCC p/n PS-5V2AEPS +5 VDC, 10W, 5% regulationVoltage supervisor limits4.75 V > Vext or Vext > 5.25 V PWR LED = Off; (power fault) 4.75 V < Vext < 5.25 V PWR LED = OnUser output voltage rangeAvailable at +5V screw terminal 4.65 V min., 5.25 V max.User output current availableAvailable at +5V screw terminal 10 mA max-Ethernet complianceDevice typeIEEE 802.3 Ethernet 10Base-TDevice compatibilityIEEE 802.3-2003 10 Mpbs Media Access Control-Ethernet connectionEthernet type10Base-TConnectorRJ-45, 8 positionCableCAT-5 shielded, unshielded twisted pairLength100 meters max.MAC address00:12:71:Cx:xx:xx, where xxxxx is the device’s serial number-EnvironmentOperating temperature range0 to 55 ° CStorage temperature range-40 to 85 ° CHumidity0 to 90% non-condensing-MechanicalDimensions127 mm (L) x 88.9 mm (W) x 35.56 (H)-Screw terminal connector type and pin outConnector typeScrew terminalWire gauge range16 AWG to 30 AWG "International buyers – please note: Import duties, taxes, and charges aren't included in the item price or postage cost. These charges are the buyer's responsibility."Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying."

Price: 757.9 USD

Location: Chula Vista, California

End Time: 2023-09-22T18:33:30.000Z

Shipping Cost: N/A USD