Woodpecker DTE Dental Wireless Curing Light 1 Sec Cure Lamp LED B/LED D

Description: Welcome to Dental-trustworthy 100% Original ! Best quality ! Best Price! Description NEW Woodpecker DTE Dental Wireless Curing Light 1 Sec Cure Lamp LED B/I LED Plus Feature: WOODPECKER LED.B:Feature:100% guaranteed original Woodpecker. Each item has unique serial number, which indicate in which region it is supposed to be sold. Woodpecker is strict with that regulation of according regional sale. As ours are to be sold in China only, we have to erase it from item, which would cause scratch-like mark. That is no damage, pls note this clearly! Wireless.Time setting: 5s, 10s, 15s, 20s.Large capacity battery. A full charge can be used for more than 500 times continuously under 10s working time mode.Low standby power consumption with seventy days` standby time.Constant light intensity. The solidification effect is not affected by the consumption of remaining power. Technical ParameterPower input: AC100V-240V 50Hz/60HzLight output: 1000mW/cm² -1200mW/cm²Net weight: 145gDimensions: 260mm×31mm×34mm LED B Packing List1 X Curing light1 X High capacitance rechargeable battery1 X Charger1 X Charger socket *********************************************************************************************************************************************************************** LED D Wireless.The battery can be replaced.Three working modes: Full, Ramping, Pulse.Time setting: 5s, 10s, 15s, 20s, 25s, 30s, 35s, 40s.A full charge can be used for over 400 times. (10s/time)Constant light intensity, the solidification effect is not affected by the consumption of remaining power.With wire or wireless. It can run directly on commercial power supply whilst the battery runs out.Technical Details:Power input AC100V-240V 50Hz/60HzLight output 850mW/cm² - 1000mW/cm²Net weight 143gDimensions 264mm × 32mm × 37mmPacking List:1 X Curing light1 X High capacitance rechargeable battery1 X Charger1* Curing light holder *********************************************************************************************************************************************************************** WOODPECKER I LED Plus (Radom Color): Brand: Woodpecker 100% original promise !Wide spectrum, High light intensity, Focused lightConstant power output, born for teeth restoration360° curing, reach every angleFluid design, better hand feelingUpgraded light intensityTwo modes for optionWith the maximum light intensity of 2300mw/cm2curing 2mm resin in 1 secondWhich makes it especially suitable for orthodontic brackets, porcelain verneers and post-core adhensives. Technical parameter1. Light output: 1000 mW/cm2 ~2500mW/cm22. Wave length: 385nm-515nm3. 360° rotatable head4. 1 sec for curing5. Time setting:Turbo (P1)-1s, 3s ,2300~2500 mw/cm²Normal (P2)-5s, 10s, 15s, 20s,1000~1200mw/cm² Dimensions: 25mm×25mm×240mmNet weight: 278gPower Input: 100V to 240V, 50Hz/60 HzWave length: 385nm-515nmLight intensity：1000mW/cm²-2300mW/cm² *********************************************************************************************************************************************************************** LY-A180: Classic rechargeable light curing unit: Environmental colorful plastic shell; Lotus charging pedestal; Handle can be placed horizontally / upright, to ensure that the light guide stick is not easy to break; 5W high power LED; High permeability rate of glass fiber-optic, strong, flashing, gradually strong 3 modes, large capacity lithium battery, automatic standby/shutdown, low battery warning, suitable for all brands of resin materials; long standby time of 90 days or more. Be charged one time, in accordance with each working time of 20 seconds, it can be used continuously for more than 130 times. Operating mode diagram:1. Power switch2. Low battery alert3. Strong mode indicator light4. Flashing mode indicator light5. Gradually strong mode indicator light6. Mode select switch7. Be adjusted in 5-40 seconds, shut down automatically . Without any operation in 20 seconds. Technical data:Package: 190×98×60mSuitable temperature: 5℃~50℃Solidify time and depth: 5s/3mmLight wavelength: 420-480nmLight intensity: 1200-2000mw/cm2Gross Weight: 0.30KgInput Voltage: 110V-240VAC, 50-60HzOutput Voltage: DC 4.2VBattery: Lithium-ion batteryCapability of Battery: 2200mA *********************************************************************************************************************************************************************** DENTMAX LED.B:Feature:100% guaranteed original DENTMAX. Wireless.Time setting: 5s, 10s, 15s, 20s.Large capacity battery. A full charge can be used for more than 500 times continuously under 10s working time mode.Low standby power consumption with seventy days` standby time.Constant light intensity. The solidification effect is not affected by the consumption of remaining power. Technical ParameterPower input: AC100V-240V 50Hz/60HzLight output: 1000mW/cm² -1200mW/cm²Net weight: 145gDimensions: 260mm×31mm×34mm LED B Packing List1 X Curing light1 X High capacitance rechargeable battery1 X Charger1 X Charger socket *********************************************************************************************************************************************************************** Xlite2 neo:Light Source: Broad Band LED;Wavelength Range: 385 - 515 nm;Light Intensity: > 2300mW/cm²;Battery: Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);Power Adapter Input Power: AC 100-240V 50 / 60Hz;Charging time: about 45 minutes.Size:Handle: Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm(all of the above are the largest size)Weight: Handle: 96 grams; Charging seat: 99 grams;Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);Operating relative humidity: 30% - 75%;Operating environment pressure: 700hPa - 1060hPa;Color Choose: White/ Black （Radomly color） Package Contents:1 × host handle;1 × charging base;1 × power adapter;1 × user manual. Operation and function description:The entire handle is only one button, light built-in button.1. For the first time, charge the light curing handle first. Plug the USB2. cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finallyPut the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then putthe handle on the charging stand. Charging instructions are as follows:| Emerald Flashing | Battery charging;| Emerald green light | battery fully charged; handle removed thecharging seat, the restoration of the previous working mode.3. Working mode selection, by pressing the button for 2 seconds to4. release to switch the working mode.| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW/cm².| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²3. Turn the light curing lamp on and off, press the button briefly.4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby. Package including: 1 Set ( radomly color) *********************************************************************************************************************************************************************** DMX iLED Ⅱ(White/Black Optional):Feature: Light Source: Broad Band LED; Wavelength Range: 385 - 515 nm; Light Intensity: > 2300mW/cm²; Battery: Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes); Power Adapter Input Power: AC 100-240V 50 / 60Hz; Charging time: about 45 minutes. Size:Handle: Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm(all of the above are the largest size) Weight: Handle: 96 grams; Charging seat: 99 grams; Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F); Operating relative humidity: 30% - 75%; Operating environment pressure: 700hPa - 1060hPa; Color Choose: White/ Black （choose the color you like） Package Contents: 1 × host handle; 1 × charging base; 1 × power adapter; 1 × user manual. Operation and function description: The entire handle is only one button, light built-in button. 1. For the first time, charge the light curing handle first. Plug the USB 2. cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows: | Emerald Flashing | Battery charging; | Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode. 3. Working mode selection, by pressing the button for 2 seconds to 4. release to switch the working mode. | Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW/cm². | Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ² 3. Turn the light curing lamp on and off, press the button briefly. 4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby. *********************************************************************************************************************************************************************** 2001B:Specifications:Light Density ≥2700mW/cmBattery ：3500mAH Input Voltage :AC100-240 Power: 12W Wavelength：400nm - 490nm Features:1. Lithium battery2. Pure LED blue light and no flicker 3. Aluminium body4. 3 second can make it! (selection from 2-6 seconds) Package：1. Light guide 2. Circular eye-protector3. power adapter 4. Charging base5. Main body 6. Manual *********************************************************************************************************************************************************************** DMX iLED:1.INTRODUCTIONThis product is used in fast solidification by lighting dental resin. It is a new generation of standard developed LED curing light, with humanity intelligent chip, the world advanced high intensity LED light and Li-on rechargeable battery. It can cure all the dental resin in the market nowadays, 2.PACKING LISTMain Body: 1Pc Light Source:: 1PcCharge Base: 1Pc Adapter: 1PcUSB cable: 1Pc Light Protect: 1PcLens: 5pcs Test block:2pcs 3.TECHNICALPARAMETERS3.1 Main Unit Battery Voltage DC3.7VBattery Capacity 1500mAhWave Length 385～515nmLight Density P1(9W) ≥ 2300mmw/cm²P2（5W）≥1200mw/cm²Charging time 3 hours approxWeight 550gPacking size L205 x W109 x H77mm 3.2AC AdapterRated input voltage AC100-240V 50/60HzOutput voltage DC 5V/MICRO USBOutput current 1A 3.3 Operation Conditions Environment temperature +5 ℃ ~+40 ℃Relative humidity 10%~80%RHAtmospheric pressure 50~106KPa 4.Use Method4.1 ChargePut the curing light into the charger base, the blue light is shining one by one. When it is done, all of the blue lights are on.It takes about 3hours. Take care not to charge more than 7hours. Remove the adapter from the power supply after charging.Note: Can charge with the main unit socket also. When charging, theLED screen show CH; when done, the LED show FU 4.2 Operation Instruction4.2.1Press M orTbutton to power on.Ifpress ON/OFF button, will light the Light source.4.2.2 Set up Mode: P1(9W,≥2300mw/cm²) The actual measured value 2800mw/cm²P2（5W，≥1200mw/cm²） 4.2.3 Setup Time:P1--1/3/5s P2--6/10/15/20s4.2.4Press ON/OFF button to light on the LED curing light. Ifsome wrong happened, the LED screen shows Er.4.2.5 The main unit will power off by itselfif without any operation about 2minuts. Caution: the curing light can not be pointed at the patient's eyes while it is operating. If any accidents happen, go to the hospital immediately 5.Precautions5.1 This machine is precise opticalequipment,it should use in the clean and dry place.5.2 Remove adapter from the power supply after charge. 5.3 Do not touch the battery electrodes by any metal objects.6.Cleaning & Sterilization6.1 CleanWipe the main unit with neutral detergent if needed. 6.2 Sterilization6.2.1 The light source can be high pressure autoclaved. Autoclave it after each use with seal bag.6.2.2Don't autoclave any parts(the main unit and charging base)other than those that can be subjected to autoclave sterilization.6.2.3 Autoclave up to a max.135℃. It's recommended to autoclave for 20min at 121℃ or 15 min at 132℃.Notice: Don't use any solvent such as benzine and thinner for sterilization.7.Transportation And Storage1)Lay lightly during transportation, avoid strong shake 2) Storage condition:a. Ambiance temperature:-10~～40℃b.Relative humidity:≤85%8.Disposing productPlease consult with dealer from whom you purchased it about waster despoil.9.WarrantyManufacturer warrants its products to the original purchaser against defects in material and workmanship under normal practices of installation, use and servicing. This unit is guaranteed for its designated use against original defects in materials and workmanship for a period of 12 months from date of purchasing. *********************************************************************************************************************************************************************** LY-C240:Feature:1.Super 10W high power LED bulb.2.360° rotating light source, 90° right angle illumination.3.The 3 mm resin can be cured by strong light for 1 second, and the light intensity is greater than 2000 mw/cm24.The outer casing is made of environmentally friendly plastic material, which is beautiful and practical.5.Strong light, pulse, fade-on three working mode selection, 1~40 seconds working time. Parameters:Packing specification:10.25*6.5*2.56inNet Weight:26.1 ozGross Weight:28.2ozOutput voltage:110v-220VAC, 50-60HZOutput voltage:DC5VBattery: Lithium ion batteryCapability of battery:2200mahBattery voltage:3.7VSuitable temperature:5°~50°CRelative humidity:≤80%Solidify time and depth:1s/3mmLight wavelength:420-480nmLight intensity:1200-2500 mw/cm2 Package Included:Subject*1Power adapter*1Charging base*1Instruction manual*1 *********************************************************************************************************************************************************************** MAXCURE9 (Radom Color) :Features:Power Input: 100-240VAC 50Hz/60HzPower Output: 5V DC/1AWave length: 385nm-515nmLight intensity: 1000mW/cm2– 2500mW/cm2Battery: 2600mA DescriptionLight cure unit is used for the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time, it is used to restore teeth and solidify material for whitening teeth. IndicationUsed for polymerization of light cure resin-based composites. It can be used on several different dental materials that are curable by light. Feature1.Dual intensity modeP1 High intensity modeCuring time For orthodontic brackets, post and core and curing photosensitive adhesive in porcelain veneer.High intensity modeConstant intensity: 2300-2500mw/cm Used for quick curing, ensuring enough curing depth, more efficientTime setting: 1s. 3s P2 General intensity modeCuring time For Normal resin.General mode Constant intensity: 1000-1200mw/cm for most treatment scenarios like teeth filling, restoration etc.Time setting: 5s, 10s. 15s, 20s 2.Broad-spectrum curing most materialsMost of the resins on the market use CQ as the photoinitiator, but some resins use two new types of photoinitiators, dipheny phosphorus oxide or Ivocerin, cnd the new materials containing TPO have a light bsorption peak of 405nm. If you use an crdinary narrow-spectrum light curing machine (wavelength range: 420nm-480nm), the resin is prane to incomplete curing. And we know that incomplete composite curing often leads to secondary pulpitis, apical inflammation, and tooth hypersensitivity.MaxCure 9 broad-spectrum light curing, newly added the 385-420nm band, the wavelength range is 385nm-515nm. It can better cure resin materials containing TPO and other emerging photoinitiators, and is suitable for ideal curing of all resin materials on the market.After a full upgrade, MaxCure 9 changes from a single blue light to a blue-violet light, which can truly cure all light-curing materials. 3.Super large battery capacity2600mAh lithiurn battery- International CB certificationMaxCure9 Battery capocity is 85% higher than normal Curing Lights 4.Constant Current DriverConstant light intensity. Constant light intensity output, stabilizing the working power 5.Light guide automatic detectionThe main unit will detect the light guide and stop the "Er" flashing if the guide is connected well, or the main unit will close down after 10s flashing.Well-installed during the period of the error alarm will stop the error alarm and the lamp will light up instantly when the lamp holder is installed. 6.Overheating protectionMain unit will detect the temperature. The overheating protection program will run when the curing light reaches a certain temperature after long time use. It' Il keep flashing until 200s later that it recovers from high-temperature. 7.Battery performance detectionWhen detect an inconstant power output from battery, the main unit will stop working to warn with flashing "Er". 8.Overvoltage protectionWith overvoltage adapter, MaxCure 9 is under protection and can' t be charged. The original adapter is recommended. Technical Specification:Humidity 10%-93%Atmosphere pressure 70kPa-106kPaTemperature -20°C - + 40°CLight power more than 2000mw/cm².3 Distinct Modes: Strong, Flashing, Gradually strong.2600 mAh Large-capacity lithium battery.5W Big power LED.Full charging available use more than 200 times.Automatic Standby/Automatic shutdown. CHARGING INDICATION:The light is on when the machine is in charging mode. Packaging:1 x Light Cure Unit1 x Adapter1 x Charging Station100 x Disposable PE isolation sleeves1 x Instructions Manual *********************************************************************************************************************************************************************** LY B200-B:Cure Light covered by ABS painting5W big power LED Cure LightHigh articulation optical fiberCure Lamp Working models:strongAutomatic standby and shut downLow Battery alertLarge-capacity lithium batteryWireless curing lamp Solidify all brands of resin materials Technology data:Capacity of battery:2200mA/h3.7vWorking voltage : AC100-240V 50-60HzWavelength: 420-480 nmLight power: more than 1500mw/cm2Solidification time and depth: 5s/3mm *********************************************************************************************************************************************************************** Guide Rod Tips(free choose):100% brand new and high quality8mm diameter for tube12mm diameter * 15mm/22mm length for metal parts Model available：Optical Fiber Guide Rod Tips（8*12*22）Optical Fiber Guide Rod Tips（8*12*15） *********************************************************************************************************************************************************************** Guide Protective Sleeves:NOTICE: Curing Light Lamp Guide Rod NOT INCLUDEDSize: 20mm*82mmPackage: 200 pcs per box *********************************************************************************************************************************************************************** Led Light Meter:Feature:LED Light Meter:Using a light guide, center the light source over the detector window read the useful curing power in mw/c㎡Used to test the curing power of dental curing light etc.Interpreting the results:Under 300: Indicates low output300-500: Test composite to determine curing time500-800: Use recommended during time appropriatelyOver 800: High output-reduce curing time appropriately. *********************************************************************************************************************************************************************** LED Whitening Tip 12*15mm - Fits for curing light - The bottom of the tip is 12mm Specification:- Material: High Quality Plastic- Color: Transperant- Size: 12x15mm / 0.47x0.59 inch Package Includes: 1x Teeth Whitening Tip ************************************************************************************************************************************************************************ Wavelength：440-480nm Light power：5W Intensity：800-1400mw/cm² Battery：Li-on 800mAh Input voltage：AC100-240V, 50/60Hz 0.4A Max Output voltage：DC 5V/1.5A Net Weight：155g Mode selection：P1, P2, P3 Solidification time：1S,3S,5S,10S,15S,20S Features: ·Produce the maximum light intensity safely. · A high intensity of 1400 mW/cm2. · Offers extremely short curing times of no more than 3 seconds. · Cordless, highly portable and light weight (only 155g). · High-performance Li-ion battery technology. · LED panel conveniently indicates a countdown curing time. · Battery can be fully recharged in 90 minutes. · Battery with protection against over-voltage, over-current and short circuit. · 3 versatile curing modes for every indications. · Automatic power off, low battery alert. · Color : White . Operation conditions: Storage Condition: Temperature: +10℃+40℃Humidity: 30%-75%Atmospheric pressure: 70KPa-106KpaEnvironment Conditions: Not near from fire equipment or flammability material.Packing list: The host * 1 Metal lamp holder *1 The silicone base *1 Power adapter *1 Disposable protective sleeve *1 Shade plate *1 Product specification *1 ************************************************************************************************************************************************************************ Using a light guide, center the light source over the detector window read the useful curing power in mw/cãŽ¡Used to test the curing power of dental curing light etc.Measures useful curing energy up to 3500 mW/cm2 100% Woodpecker originalBrand: WoodpeckerModel: LM-1 Features:light, compact designcapable of measuring both LED and halogen curing lights.Able to measure intensity up to 3500mw/cm2 ************************************************************************************************************************************************************************ ************************************************************************************************************************************************************************ Woodpecker LED Q: Sealed ,Connect to Dental UnitTime setting 10s,20s,30sWorking Model: Full Features: FDA and CE0197 Certificated. - 360 Degree rotary head, extend the possibility. - Ergonomics design, optimize the hand-grip use. - 3W high power blue light LED. - This device can cure composite resin not less than 4mm in 10 seconds. Packing listMain unit x1pcsOptical Fiber x1pcsLight Hood x1pcsinstruction book x1pcsProduct certificate x1pcsWarrenty card x1pcs FDA Statement The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. Shipping Destination Delivery Time Working Days 7-10 10-15 15-25 25-40 >50 US Item arrived 80% 10% 8% 1% Refund ASIA Item arrived 30% 40% 20% 10% Refund EU Item arrived 20% 20% 50% 10% Refund AU Item arrived 30% 30% 20% 20% Refund other countries Item arrived 5% 10% 10% 60% -- Feedback Returns If the item you received is damaged or defective,Please message to us immidately.We will free exchange or refund.We will pay the return shipping costs if the product is defective or the return is a result of our error. If the item is returned for any other reason you are responsible for the return shipping charges.You can return your purchase for up to 15 days from the date of delivery. No refund will be issued if the product shows signs of use. Returned package must be in the original packaging, everything must be in new condition, No missing parts.Our guarantee does not cover accidental damage or wear of product caused by customer.Thank you very much for your understanding! Contact us Our working timeMonday To Friday: 8:30 am --- 12:00am1:30pm ---5:30pm(Please Refer to Beijing Time.)

Price: 7.5 USD

Location: beijing

End Time: 2023-11-09T03:09:56.000Z

Shipping Cost: 0 USD