XXXL Body Armor Flectarn Full Plate Carrier MOLLE Tactical Vest 3A

Description: Full Body Armor Plate Carrier Vest IIIA NIJ MOLLE Kevlar included, size XXXL color Flectarn Normal 0 false false false RU X-NONE X-NONE Normal 0 false false false RU X-NONE X-NONE This model complies with NIJ Standard-0101.06 for Ballistic Resistance of Body Armor The threat level rating of the vest is IIIa NIJ Manufacturer is Ukrarrmor Model "Shark" Fl3XlType: Body armor vestsize: XXXLReference material of the vest - CorduraThe vest is equipped with MOLLY Color: Flectarn Condition: new Measurements:Chest Width: 17'' / 43 cmWaist Width: 19.6'' / 50 сmWaist circumference: 47 - 53'' / 119-135 cmHeight* : 5'11" - 6'2" / 179 - 187 cm* If you are taller, then you need the XXXL long, if less, it means XXXL short version. The “Shark” vest offers full IIIA ballistic protection, including the back, chest and sides of the torso, as well as shoulders, neck, and groin. The vest "Shark" is designed for heavy use, even in hot climates: when the waist fasteners are set slightly loose, the vest balances on the wearer’s torso allowing breathing room between the plate carrier and the wearer’s skin. Loose wearing of the vest is not advisable during combat, but having the option prevents the need for removal of the vest to cool down during non-combat. The front and back of the vest have full-size pockets, exterior to the Kevlar “IIIA Soft Armor”, which are hard armor plate ready. Adding hard armor to the vest would increase its front and rear ballistic rating to III or IV (depending on the plates you choose to add). Hard armor plates are not included in this listing. Independent of the exterior pockets for hard armor plates, the entire surface of the vest, neck and shoulder pads, and groin pad are fitted with custom-cut IIIA Kevlar ballistic armor. The Kevlar armor is bendable and lightweight making it an ideal choice for balancing protection and maneuverability.Modular vest "Shark", has an improved ergonomic configuration of the security elements, and also allows to use them depending on the specifics of the tasks and the likely threats. The vest "Shark" is a modular system and can completely disassemble. Made of a very robust and high-strength quality Cordura fabric (high-strength polyamide fabric). 1. Regulation and the compound vest "Shark" in the shoulder area by means of a double overhead valves, which are attached via Velcro hook and loop fastener element to protect the breast from above and below, which provides an enhanced fixation. At the end of the shoulder edges of the valve mounting the chest sewn belt protection belt that provides quick release items of body armor for the urgent release of the user on their own or with the help of the second persons in the event of an emergency.2. Completion of bulletproof vests "Shark" can be supplemented with hard armor plates (at an additional cost).3. On the inside surface of the cover in the flak vest there is a special voluminous cushioning material, which has channels that allow airflows to cool and remove moisture from the body.4. In the absence of removable side protection, fastening and regulation of the bulletproof vest at the waist is carried out by means of a belt and textile Velcro. 5. The fastening of the left and right axle shafts of the side protection in front has a double fixation with a textile fastener. Side protection is attached to the breast protection cover and is additionally covered with a breast valve. On the edges of the left and right side protection elements, sewn belt tapes for their quick detachment from chest protection. Length of side wings adjustable.6. In the side compartments, also and rigid armor plates can be placed.7. The left and right side elements of the body armor are protected by the MOLLE system from the back, this fastening allows you to adjust the bulletproof vest at the waist. This allows you to wear a vest like in summer on a T-shirt and in winter on a warm volumetric jacket.8. The groin protection element is fastened with belt strips to the MOLLE slings located on the bottom of the chest cover from the inside.9. Pockets for armored plates. This version of the vest "Shark" provides pocket for the front and pocket for the back plates. The pockets can hold plates of XL "Extra large" 30x35 cm / 12”x14”.10. The vest has 7 rows of MOLLE sling lines, for which you can install all necessary pouches, Mags Kevlar ballistic armor, rated III-A (USA) Every square inch of stitched material is packed with custom fit Kevlar body armor: The vest front, the vest rear, each side of the vest, the detachable shoulders and 2-piece neck collar, and the groin protector.The standard version of the vest consists of 9 elements: The vest front, the vest rear, each side of the vest (left+right), the detachable shoulders and 2-piece neck collar, and the groin protector. For additional cost the body armor can be completed:- armor plates in accordance with the standard of Ukraine (DSTU) or the US standard. The hard armor plates are located in the extra pockets of the body armor vest. * In addition, the vest can be equipped with various pounches and Mags, as well as to increase the range of protective vests, by the following ingredients:- protection of the pelvis (coccyx) of the lower rear side;- deltoid axillary lateral zone elements;- camerbands for extra side plates; By buying this vest in any of the available complete sets and color schemes, you get what you see. If you have any questions, please ask, do not hesitate.So welcome to buy my lot. Enjoy your shopping, I still have a lot of other products of military and sporting themes.

Price: 1235 USD

Location: Kyiv, default

End Time: 2024-10-06T08:14:09.000Z

Shipping Cost: 65 USD